| Make | Model | Problem | Solution | Date |
| | | |
| Found: 4551
|
| Philips | 14PV172 | Start up problems after replacing TS7352 | When TS7352 is replaced, it can happen that the set doesn't start up properly.
There are 2 possible solutions for this problem:
- use SGS type MTP3055E (4822 130 63726).
- In case of a motorola type MTP3055V (4822 130 60838), add a 22 uH coil soldered | 14-09-04 |
| Philips | 14PV182 | dead, tripping | T7583 BUT12AF s/c on main PCB | 14-09-04 |
| Philips | 14PV182 | No R/C operation | Replace I.R pickup unit on Vcr front Pcb Part 4822-218-11745 (SEME) ?3.44 | 14-09-04 |
| Philips | 14PV182 | No R/C operation | IR pickup module has no o/p although its supply is correct - replace part No 4822-218-11745 | 14-09-04 |
| Philips | 14PV182 | St/by only with vcr shuffling constantly | LOPTx - had hole in it | 14-09-04 |
| Philips | 14PV182 | tripping on & off at 1 sec intervals | MC4403 chip IC7130 in psu | 14-09-04 |
| Philips | 14PV182 combi | Dead with tape stuck in machine | LOPTx | 14-09-04 |
| Philips | 14PV182/05 | OSD missing | L802 7.4Mhz osc coil o/c pt no 4822 157 71289 | 14-09-04 |
| Philips | 14PV183 | To activate/deactivate "hotel mode" | Press "Stop" on r/c & "Stop" on keyboard for 5 secs whilst on Ch 38 | 14-09-04 |
| Philips | 14PV183 | To enter service mode | Press "Stop" on r/c & "Play" on k.board for 5 secs | 14-09-04 |
|
|
| Philips | 14PV183etc | Hotel mode activate/deactivate | Press "STOP" on handset & "STOP" on keyboard together for 5 secs whilst on Chan 38 | 14-09-04 |
| Philips | 14PV183etc | No Chan +/- on R/C after EEPROM replacement | Enter service mode & set correct option number - to be found on back plate of set | 14-09-04 |
| Philips | 14PV183etc | Service mode adjustments | Press "STOP" on handset & "PLAY" on keyboard together for 5 secs | 14-09-04 |
| Philips | 14PV184 | Menus not displayed | L1802 on bottom panel across pins 42 & 43 of micro IC7801 | 14-09-04 |
| Philips | 14PV184 | Reverts to st/by at sw on aft LOPTx replacement (LED goes from brief green to red) | Eventually comes on with dull grey raster. PROT line on micro IC7801 pin 53 vcr pcb only 1v (5v) - check at D6568 LH plug 1923 - prot Tr 7550 BC547 leaky (front left edge of tv pcb) | 14-09-04 |
| Philips | 14PV200/07 | "N ACT" shows at sw on | Switch the combi off with the mains switch. depress and hold both the wind & rew buttons on the combi while switching back on (Keeping the buttons pressed for around 5 seconds) Release the buttons and this should clear the memory and allow the combi to be setup as normal | 14-09-04 |
| Philips | 14PV200/07 | Dead apart from popping sound at sw on | D6391 BYW98 200 rated at 3A s/c - used BY399 in lieu | 14-09-04 |
| Philips | 14PV202/07 | Int blows fuse at sw on | Replace degauss coil, degauss posistor and 1.25 amp fuse | 14-09-04 |
| Philips | 14PV210 | Fault codes | record led flashing >>>error in eeprom1[ic7818]; timer led flashing>>> error in eeprom2[ic7801]; stdby led flashing>>> error in textmicro[ic7804] | 14-09-04 |
| Philips | 14PV210 | No pic; R3199 burnt | R3199 (9K2) and D6183 (SMD) Used 1N4148 in lieu | 14-09-04 |
| Philips | 14PV263 | Calling installation menu | The installation menu is activated by the following procedure:
- switch on the set by means of the stop key.
- Press simutaneously the cursor left and the cursor right key on the remote control. | 14-09-04 |
| Philips | 14PV263 | Codenumber correction | The codenumber of pos. 1701 (tuner) for 14 inch sets with IEC input is 4822 210 10691 (UV916S). | 14-09-04 |
| Philips | 14PV263 | Codenumber correction | The codenumber for the scanner-motor (POS. 34) in the Service Manual is wrong.
The correct codenumber is 4822 361 215 48. | 14-09-04 |
| Philips | 14PV263 | Codenumber information | The codenumber for the spacer between on/off switch and the knob (pos 3) is 4822 402 10702. | 14-09-04 |
| Philips | 14PV263 | Codenumber information | Please add following codenumbers to the Service Manual:
Lift-flap 14PV263/01 : 4822 443 10404
Lift-flap 14PV263/02 : 4822 443 10404
Spring for lift-flap : 4822 492 70896 | 14-09-04 |
| Philips | 14PV263 | Correction service Manual 14PV263/01 | The indication of the small-signal PCB (page 1-3) is wrong. The right indication is PSSPP3/GPVXF.
This PCB is only applied in 14PV263/01. | 14-09-04 |
| Philips | 14PV263 | How to activate/de-activate "Hotel mode" | Activation:
- set volume to desired level.
- select programm 38.
- press the STOP button of the remote control AND the STOP button of the VCR for about 5 seconds, until the message H+ appears.
De-activation:
- set volume to desired level.
- select p | 14-09-04 |
| Philips | 14PV263 | Key set | The key set assy has been codified for all B-range TVCR's. This will allow to change the keys without having to change the complete frame. Servicenr. 4822 410 11075.
Key set for: 14PV263/01/02/08/13 - 14PV264/39 - 14PV163/05 - 14PV172/01/05/08/13/39 - 14 | 14-09-04 |
| Philips | 14PV263 | Memory erase procedure | The contents of the memory can only be cleared via the service mode. This option is not available for end users. (Risc of destroying option codes).
Service mode: press "STOP" on Remote Control and "PLAY" on the set for 5 seconds. Select the second page | 14-09-04 |
| Philips | 14PV263 | Set produces audible noise in stand-by | Add a small LEBL (leading edge blanking) PCB, to avoid auto oscillation of transformer 5330 (or 5331). A modification letter is included with the lable PCB. This PCB is available with service nr. 4822 214 12173.
Since production week 9723 this circuit is | 14-09-04 |