| Make | Model | Problem | Solution | Date |
| | | |
| Found: 4551
|
| Philips | ANUBIS-S | Mains fuse 1500 fails constantly | In case the mains fuse of a 25" Anubis S BB set constantly blows,
it is recommended to upgrade it to a 4A type:
Change fuse 1500 to T4A 4822 070 34002
Also update the text T3.15A on the service printing to a
sticker with the text T4A.
REMARKS | 14-09-04 |
| Philips | ANUBIS-S | Modification | Modification
------------
For ALL ANUBIS-S WITH NO SECAM RECEPTION
IC7225 TDA8362 is replaced by TDA8361 in all ANUBIS-S sets with
no SECAM reception possibility from production week 9416 onwards,
so,
IC7225 = TDA 8361E/N3 4822 209 33479 (PAL + NTSC, n | 14-09-04 |
| Philips | ANUBIS-S | No +95V/+115V from power supply | In case of a failure of one of the components TS7513, R3503 or
D6502 till D6505, it is strongly recommended to replace all of
these components.
For service codes see,
Service Manual ANUBIS-S AA
GB 4822 727 19707
E 4822 727 19719
ANUBIS-S BB
| 14-09-04 |
| Philips | ANUBIS-S | No colour at PAL in case of disconnected 2CS+I/O+Ampl panel | In the service position, the main panel of the Anubis S BB is
disconnected from the 2CS+I/O+Amplifiaction panel.
For Anubis S BB sets with 2 HEF shift register in cascade (as how
it is used by now for controlling an Anubis S BB set with
incredible stere | 14-09-04 |
| Philips | ANUBIS-S | No NICAM sound | In case of no NICAM sound it is recommended to replace on the NICAM
panel:
R3055 to 560 ohm 2% 0.25W 4822 051 10561
(diagram K page 21 in the service manual
Anubis S BB 4822 727 20262)
REMARKS :
Lower R3055 gives a higher starting current fo | 14-09-04 |
| Philips | ANUBIS-S | No picture | Apply a slight force to further insert the EHT cable into the line
output transformer 5445.
REMARKS :
Above cure is only relevant for sets with LOT 4822 140 10525
or 4822 140 10557.
When replacing the above mentioned LOT's, please take note of t | 14-09-04 |
| Philips | ANUBIS-S | No picture after picture tube flash over | In case after a picture tube flash over (one of) the video output
transistor(s) BF422 (TS7305, TS7318, TS7327) failed, it is
recommended to:
1. Change 2337 to 4n7 2kV 4822 126 12833
2. Delete and short R3336 with a wire jumper
3 | 14-09-04 |
| Philips | ANUBIS-S | No stereo, no +95 volt | R3523 is interrupted, D6519 and C2519 (= capacitor between D and
S-7513) are short circuited.
Remove C2519. Replace R3523 - 390K - 4822 116 52278
Replace D6519 - BTZ03-C15 - 5322 130 31574
| 14-09-04 |
| Philips | ANUBIS-S | One colour missing or no picture | In case of 1 colour missing or no picture, it is recommended
to solder across R3301 on the CRT panel on the copper side:
100nF 10% 250V 4822 121 41689
This capacitor protects the 3 BF422 video output transistors
TS7305, 7318 and 7327 against flash
REM | 14-09-04 |
| Philips | ANUBIS-S | Only for ANUBIS-S BB 25
Adaption in the frame par | Only for ANUBIS-S BB 25
Adaption in the frame part of 25" Anubis S BB
---------------------------------------------
From production start onwards the following modification is done in
the convergence circuitry in the frame part of diagram AA:
R3403 shou | 14-09-04 |
|
|
| Philips | ANUBIS-S | Only for ANUBIS-S BB 25" Codenumber information | Only for ANUBIS-S BB 25"
Codenumber information
----------------------
The missing service codenumber for the bridge coil L5480 in the
east / west part of the 25" ANUBIS S BB (diagram AA) is:
4822 157 71149
| 14-09-04 |
| Philips | ANUBIS-S | OSD characters too thin | It is recommended to replace in the control part:
R3715 by 1k2 (4822 116 52207)
REMARKS :
Introduced in production week 9408
| 14-09-04 |
| Philips | ANUBIS-S | Picture jittering when OSD is recalled, all versions | Replace R3605 by 2k (4822 116 52253) at pin 20 of uP
REMARKS :
Introduced in production week 9328
| 14-09-04 |
| Philips | ANUBIS-S | Picture tube 20" Anubis S AA and CC A48KXR98X | Picture tube 20" Anubis S AA and CC A48KXR98X (4822 131 20577)
---------------------------------------------------------------
Only for ANUBIS-S 20" AA and CC
For both Anubis S AA and CC picture tube A48KXR98X (neutral
hemisphere) is no longer available | 14-09-04 |
| Philips | ANUBIS-S | Picture width too small during off-air reception. | Delete R3453, R3454 and L5454 in the line defl flyback circuitry
and place jumper at position 9454.
REMARKS :
Introduced in production week 9340 in Spore and week 9346 in LFL
Thailand.
| 14-09-04 |
| Philips | ANUBIS-S | Pix blanks at certain prog. nrs | Software bug.
Micro Processor need to be replaced.
Change from version SA FHV 1.9 to SA FHV 2.1
| 14-09-04 |
| Philips | ANUBIS-S | Plop at switching on/off NICAM sound | In case of a NICAM switch on/off plop it is recommended to change
on the NICAM module (diagram K) of the Anubis S BB:
* Place elco 47uF 20% 25V (4822 124 40433) with + to pin 9 of
IC7075 and with - to ground
* Replace C2065 and C2076 by 470nF 10% 50V ( | 14-09-04 |
| Philips | ANUBIS-S | Plop at switching on/off NICAM sound | In case of a NICAM switch on/off plop it is recommended to change
on the NICAM module (diagram K) of the Anubis S BB:
* Place elco 47uF 20% 25V (4822 124 40433) with + to pin 9 of
IC7075 and with - to ground
* Replace C2065 and C2076 by 470nF 10% 50V ( | 14-09-04 |
| Philips | ANUBIS-S | Plop sound at switch off of the set | For mono versions:
Replace D6109 by BZX79-C2V7 (5322 130 34563)
For stereo PB (+ BTSC) versions:
Replace D6807 and D6808 by LLZ-C2V7 (4822 130 81138)
REMARKS :
Introduced in production week 9331
| 14-09-04 |
| Philips | ANUBIS-S | Powers supply output voltages for the different sc | Powers supply output voltages for the different screensizes
for ANUBIS-S AA/BB/CC/DD
------------------------
For adjusting the power supply output voltage (via R3512) following
survey gives an overview of the values for the different screensizes
of all c | 14-09-04 |
| Philips | ANUBIS-S | Protection of part of EEPROM | Protection of part of EEPROM
----------------------------
For all versions:
For software number 1 (6k no TXT) and software number 2 (8k TXT)
ADDRESS 255 should be filled with DATA 232 after replacing the
EEPROM. This to make sure the right part of the EE | 14-09-04 |
| Philips | ANUBIS-S | Purity problem (patches on screen) | Change item 3501 from 18 Ohm PTC to 9 Ohm PTC
Service code 9 Ohm PTC is 4822 116 40277
| 14-09-04 |
| Philips | ANUBIS-S | Purity problems 20" versions | Replace PTC R3501 by a 9 ohm version.
Code number 4822 116 40277. | 14-09-04 |
| Philips | ANUBIS-S | Service manual correction LATAM service manual | Service manual correction LATAM service manual
----------------------------------------------
In service manual 4822 727 19719 the following components are
changed at production start only TRINORMA sets:
C2272 becomes 10nF (4822 126 12642)
C2273 becomes | 14-09-04 |
| Philips | ANUBIS-S | Set is switched in protection (switched in to standby) | Check if pin 16 of uP IC7600 is continiously "low". If so the set
is in protection. Check D6618 in the control part and replace if
necessary by BZX79-B9V1 (4822 130 30862)
REMARKS :
Introduced in production week 9408 | 14-09-04 |
| Philips | ANUBIS-S | Snowy picture | Add a diode 1N4148 (4822 130 30621) in series with item 5002.
Connect the anode at the L5002 side and the cathode at the
junction of C2002 and pin 12 of the tuner
REMARKS :
Introduced in production week 9410
The diode ensures a correct supply v | 14-09-04 |
| Philips | ANUBIS-S | Sound distorted in theatre mode if volume is set from mid to highlevel | Modify following components on incredible sound panel.
R3205 and R3405 into 1k5 - 4822 051 11502
C2302 and C2305 into 100nF - 5322 121 42386
R3305 and R3302 into 560E - 4822 050 15601
R3500 into 220E - 4822 052 10221
R3300 and R3303 into 1k2 - 4822 050 11 | 14-09-04 |
| Philips | ANUBIS-S | Sound distortion at theatre mode | To solve the problem make next changes:
On incredible sound panel Pos. number
Change to 1K2 4822 116 52207 3205,3405,3300,3303
Change to 100 nF 5322 121 42386 2302,2305
Change to 560E 4822 116 52226 | 14-09-04 |
| Philips | ANUBIS-S | Sound in picture | Replace L5014 by 0.68uH (4822 157 63065)
REMARKS :
Introduced in production week 9319
| 14-09-04 |
| Philips | ANUBIS-S | Sound in picture (interference in picture) | In case of sound in picture interference it is recommended to:
Place C2170 by 2n2 20% 50V 4822 126 12639
REMARKS :
Introduced in production week 9407
| 14-09-04 |