| Make | Model | Problem | Solution | Date |
| | | |
| Found: 4551
|
| Philips | 31DV3 | Change of threaded in time after rewind | After rewind to tape begin, the above VCRs go to the threaded in position. If no function is requested, after 6 minutes the VCR dethreads to the stop position where it stays for 2 minutes before returning to standby.
From week 41 the waiting time at th | 14-09-04 |
| Philips | 31DV3 | Intermittent loss of picture and sound, teletext also affected | Check EPROM on the teletext PCB.
Check IC 7751 (KSTX1), might be faulty when warm. | 14-09-04 |
| Philips | 31DV3 | Not recording Sound | The cause of this fault was traced to 3230, the resistor had gone high.
The resistor had changed from 2k7 to 4k3. | 14-09-04 |
| Philips | 32 PW 9503/12 | Problems with a Philips 32 PW 9503/12, chassie MD 2.22
Shortcircuit in HV-transistor BU2520D, short in 2418 (85 ohms). 220pF
Have replaced both of them, tv started up for 1 sec with highvoltage
then to stby. Red standbylight on front is blinking rapi | also replace fet 7470 = IRF620FI
| 18-08-05 |
| Philips | 320 Mono | No picture. | C2207 , T2828. | 14-09-04 |
| Philips | 32PW6005 | Set inoperative and PTC defective. | Check and replace if necessary position 3912 on the large signal panel by 4822 116 10105
IRIS CODE : M11X | 14-09-04 |
| Philips | 32PW6005/05 SA10E | St/by only | Resolder SMD TDA8885, it is located on the sub-board next to the tuner.(Runs very hot) | 14-09-04 |
| Philips | 32PW6332 | No sound | Enter service mode & check option NI (Nicam) - should be "Y" (yes) next to it | 14-09-04 |
| Philips | 32PW6332 | Service mode adjustments | Short pins S42 & S43 on signals board (upright board on L). Now have various options available | 14-09-04 |
| Philips | 32pw6515 | hi my philips tv (32pw6515) is now stuck in standby (red led on) and no responce from either the on-board controls or remote?
| the fault on your philips tv is probably ic7064. also known as the painter ic, on the small signal board, this ic seems to be responsible for over 90% of faults on this chassis. it is a 100 pin surface mount device. i would not recommend trying to replace it unless you have a good amount of experience at soldering very small devices as it is not much bigger than a stamp, you will also need to reprogramme the eeprom ic with the options and geometry settings after replacement, i have done more than 30 and it takes me upto 2 hours | 31-10-05 |
|
|
| Philips | 32pw6515/05 | after set is on for 5 minutes there is no response from remote handset
or controls on tv | Ic 7064 on small signal board.
| 08-08-05 |
| Philips | 32PW6515/05 SA10E | Hum from front speaker | Remove link 9710 & connect link from 9710 (C2702 end) to link 9278 | 14-09-04 |
| Philips | 32PW9525 | Pumping effect (horizontaly) of the picture | Pumping effect (horizontaly) of the picture during picture changes from
low to high luminance
Implement a high voltage bleeder in the set on the following way:
Modifications on the Large Signal Panel:
Change position C2448 into 10nF (4822 121 41857) | 14-09-04 |
| Philips | 32PW9544/05M | Dead with flashing LED | St/by relay - can swap this one with degauss one for test purposes pt no 4822 280 10375 | 14-09-04 |
| Philips | 32PW9611/58 | Green LED comes on at sw on briefly then reverts to red led (St/by) with no 140v at +A | full wave bridge rects all s/c & safety res 2r7 15w. The
chopper mosfet, with strange markings was also s/c type :G239-1HEX fitted a IRF PC 50 rated at 11amp.
In lieu | 14-09-04 |
| Philips | 32PW9763/05 MD2.25E | St/by only with led flashing | Main micro on control board pin 53 stuck hi due to D6227 zener 3v3 sm o/c. For more info see TV mag Nov 2001 | 14-09-04 |
| Philips | 32PW9765 | Pumping effect (horizontaly) of the picture | Pumping effect (horizontaly) of the picture during picture changes from
low to high luminance
Implement a high voltage bleeder in the set on the following way:
Modifications on the Large Signal Panel:
Change position C2448 into 10nF (4822 121 41857) | 14-09-04 |
| Philips | 32W6332/05 | No sound | TDA2616 audio o/p ic & wickman fuse o/c | 14-09-04 |
| Philips | 34PT4822 | mono-carrier PCB-layout of L9.1A | For the above mentioned 21" sets the mono-carrier PCB-layout of L9.1A is introduced to increase the audio power and the way the SDM and the SAM is
entered is changed. They also have a new Side AV & headphone panel (E1).
The 21PT3952 and 21PT3962 are t | 14-09-04 |
| Philips | 34PT4873 | mono-carrier PCB-layout of L9.1A | For the above mentioned 21" sets the mono-carrier PCB-layout of L9.1A is introduced to increase the audio power and the way the SDM and the SAM is
entered is changed. They also have a new Side AV & headphone panel (E1).
The 21PT3952 and 21PT3962 are t | 14-09-04 |
| Philips | 37TR120 | Key set | The key set assy has been codified for all b-range tvcr's. This will allow to change the keys without having to change the complete frame. Servicenr. 4822 410 11076.
Key set for: 37TR120/01/08 - 37TR126/03/38 - 37TR125/38N - 37TVB10/39N. | 14-09-04 |
| Philips | 37TR125 | Key set | The key set assy has been codified for all b-range tvcr's. This will allow to change the keys without having to change the complete frame. Servicenr. 4822 410 11076.
Key set for: 37TR120/01/08 - 37TR126/03/38 - 37TR125/38N - 37TVB10/39N. | 14-09-04 |
| Philips | 37TR125/38 | Codenumber information | A new software version (PTCP2-7) is available for the control uP (IC 7801). Service codenumber is 4822 209 15271.
This new version is only used in the following sets:
14PV263/01, 14PV162/01, 14PV162/05, 14PV162/07, 14PV163/05, 14PV163/05H, 14PV263/01 | 14-09-04 |
| Philips | 37TR126 | Codenumber correction | The codenumber of pos. 1701 (tuner) for 14 inch sets with IEC input is 4822 210 10691 (UV916S). | 14-09-04 |
| Philips | 37TR126 | Codenumber correction for deck-up (IC7410) | The codenumber for the deckprocessor was wrong in the first Service Manual (4822 726 15451).
In service information TVCR96-01 and in the new manual the correct codenumber is given.
The codenumber for the deck-up for sets with non-turbo drive is: 4822 | 14-09-04 |
| Philips | 37TR126 | Codenumber information | The codenumber for the spacer between on/off switch and the knob (pos 3) is 4822 402 10702. | 14-09-04 |
| Philips | 37TR126 | Codenumber information | Please add following codenumbers to the Service Manual:
Lift-flap 37TR126/03 : 4822 443 10413
Spring for lift-flap : 4822 492 70896 | 14-09-04 |
| Philips | 37TR126 | Key set | The key set assy has been codified for all b-range tvcr's. This will allow to change the keys without having to change the complete frame. Servicenr. 4822 410 11076.
Key set for: 37TR120/01/08 - 37TR126/03/38 - 37TR125/38N - 37TVB10/39N. | 14-09-04 |
| Philips | 37TR126 | Preventive tip | If FET 7352 is found to be defective, it is advised to mount a 15 V zenerdiode (BZX79-C15) between the drain and the gate. Mount cathode to gate and anode to drain.
Codenumbers:
FET 7352: 4822 130 60838
ZENER (BZX79-C15): 4822 13034281 | 14-09-04 |
| Philips | 37TR126 | Set produces audible noise in stand-by | Add a small LEBL (leading edge blanking) PCB, to avoid auto oscillation of transformer 5330 (or 5331). A modification letter is included with the lable PCB. This PCB is available with service nr. 4822 214 12173.
Since production week 9723 this circuit is | 14-09-04 |