| Make | Model | Problem | Solution | Date |
| | | |
| Found: 4551
|
| Philips | 14TVCR240 | Spare part info | As a Service spare part, the picture tube will be changed back to a Philips model. Its code is: 4822 131 20623.
If your set was previously equiped with an Orion picture-tube, please make additionally the following modifications when mounting this Philips | 14-09-04 |
| Philips | 14TVCR240 | Spare part information | Concerns sets produced from week 9608 until 9647. Motor holder with reverse prism included:
In sets produced before week 9647 the reverse prism is a fixed part of the chassis and not available as a spare part.
From week 9647 onwards a motor holder (pos. | 14-09-04 |
| Philips | 14TVCR240 | Spare part information | A repair kit , containing PULLEY SHAFT + WORM SHAFT (POS. 47+48) is delivered with codenumber 4822 310 10657.
This kit can be used for all TURBO- and ECO mechanisms ! | 14-09-04 |
| Philips | 14TVCR240 | Start up problems | When the set is switched on by the mains-switch while a cassette is in the set, the front LED starts blinking, but the set doesn't start.
Solution: Check the primary voltage (Ubat) and adjust this for 14" sets to exactly 101.5 Volt. (See chapter 3.1.1 of | 14-09-04 |
| Philips | 14TVCR240 | Start up problems after replacing TS7352 | When TS7352 is replaced, it can happen that the set doesn't start up properly. There are 2 possible solutions for this problem:
- use SGS type MTP3055E (4822 130 63726).
- In case of a motorola type MTP3055V (4822 130 60838), add a 22 uH coil soldered i | 14-09-04 |
| Philips | 14TVCR240 | Tripping - HT rises to 170v (should be 110v) | R3343 5R6 safety res o/c pt no 4822 052 10568, D6335 s/c pt no 4822 130 8330 | 14-09-04 |
| Philips | 14TVCR240/05 | Tripping due to high HT | D6335 s/c UG06B (iN4148 does) & R3343 5R6 o/c in feedback reg cct | 14-09-04 |
| Philips | 14TX3504 TX3 | Frame collapse. | R423 ( 33k ) o/c. | 14-09-04 |
| Philips | 14VP163 | WHITE RASTER WITH FLYBACK LINES THEN STANDBY | REPLACE R3592 | 14-09-04 |
| Philips | 14VP184 | DEAD, BLOWING FUSE | REPLACE POSISTOR | 14-09-04 |
|
|
| Philips | 14VP274/05 | SOUND OK NO PICTURE | IF NO HEATERS REPLACE R3532/3537 AT REAR OF TV PCB BOTH 4R7 FUSIBLE | 14-09-04 |
| Philips | 17CE1358/05B | No col | TDA2541 faulty - (pin 26 TDA3561A = 2.2v NOT 10v as marked on cct) | 14-09-04 |
| Philips | 17HT5403 | To adj sound level of this "Hotel" TV | Press Set Up then "M" then scroll down options to vol - adj vol then press "M" | 14-09-04 |
| Philips | 17PT161A | To adj tuning | Dedicated R/C reqd pt no 4822 218 21249 & must press both diamond keys together to enter tuning mode | 14-09-04 |
| Philips | 17PT165B AA5AB | Dead aft lightening strike | Replace 1571 (630mA wickman) and retune stations
(tuning memory had been wiped out). | 14-09-04 |
| Philips | 20CT4626/05T | Cracking & banging. | Drys on LOPTX. | 14-09-04 |
| Philips | 20DV1 | Poor response to Infra Red Handset operation | It is possible that VCRs of the above types and having a week code of 9042 or 9043 may not always respond to signals from the remote control handset.
Cause:A small number of capacitors fitted in position numbers 2021 and 2022 on the operating panel (JDC) | 14-09-04 |
| Philips | 20DV1 | Production change | In VCRs from WD32 onwards coil 5005 on the family board (jfb) will be replaced by a fuse.
The fuse is given the position no. 1005.
The fuse rating is 250mA/125 volt.
The code no. of the fuse is 4822 252 51142.
IMPORTANT: The fuse becomes a safety c | 14-09-04 |
| Philips | 20DV1 | Replacing the combi head | After replacing the combi head the setting of the head height is referred to in Section 2:8:4 of the IDM deck manual. The method used is to set for maximum amplitude of the control track signal. In the above mentioned VCRs the signal is amplified in a lim | 14-09-04 |
| Philips | 20HT3303 | "welcome message" doesn't come up at start up. | When the set is switched off via the mains switch and is switched on again after more than 5 minutes, the "welcome message" doesn't come up at start up.
Put the set into the SDM mode. Select the option AS (Auto start-up).
Change the option content fr | 14-09-04 |
| Philips | 20HT3303 | Service code of the FM-Radio tuner. | In the partslist of the Radio-SP/LS-Vbatt panel of the Chassis Manual L9H.2E, the service code of the FM-Radio tuner item 1901 was not indicated.
The service code is 9352 632 70112 | 14-09-04 |
| Philips | 20PT135A/42 | Philips 21'. The quality of picture (contrast) is very poor and even if i adjust it from the remote controll is still dark.I check TDA 3504 (video control combination) but still nothing..
| Could be a beam-limiter fault.
Check the voltage on the bottom end of the EHT winding, where they tap off for the beam-limiter circuit. It's quite common for the resistor from the H.T to this point to go o/c, or the decoupling capacitor to go s/c.
| 09-08-05 |
| Philips | 20PT138A | Dead | R3450 3R9 (to 5v5 supply rectifier off loptx) | 14-09-04 |
| Philips | 20PV164 | cuts out after 10 mins | replace frame IC 6510 (4822 209 13066), D6513 (4822 130 30842) and C2513 (4822 124 11539) | 14-09-04 |
| Philips | 20PV164 | goes to stby after a few mins | frame collapse due to int. D6513 breaking (BAV21, part no. 4822 130 30842). To remove protection disconnect collector of 7550 | 14-09-04 |
| Philips | 20PV164 | Int reverts to st/by | Dis'ing FOP chip stopped fault but replacement made no diff; 6513 pump up diode was faulty - used RGP15 in lieu | 14-09-04 |
| Philips | 20PV164 | Int reverts to st/by | Remove Tr7550 to disable prot cct. Field collapse int observed. D6513 faulty | 14-09-04 |
| Philips | 20PV164 | Key set | The key set assy has been codified for all B-range TVCR's. This will allow to change the keys without having to change the complete frame.
Servicenr. 4822 410 11073 - Key set for: 20PV164/02/05/08/13.
Servicenr. 4822 410 11801 - Key set for sets produ | 14-09-04 |
| Philips | 20PV164 | Modification | An early production problem appears on these sets: the AGC voltage supplied to the Tuner 1 is too high (app. 8.8V) in comparison to the supply voltage (5V). It results in a wrong correction of the AGC loop when the antenna's signal is too low (about 1,5m | 14-09-04 |
| Philips | 20PV164 | Modification | From production week 9725, the IC's SDA5649, SDA5649x and SDA5648 are replaced by a SDA5650 (4822 209 15504).
This new IC is fully compatible with the others, but has better characteristics.
In addition to this modification, R3812 on the small signal | 14-09-04 |